<big id="x777x"></big>

      <p id="x777x"></p>
      <track id="x777x"><strike id="x777x"><strike id="x777x"></strike></strike></track>
      <pre id="x777x"></pre>

      <address id="x777x"><strike id="x777x"><span id="x777x"></span></strike></address>

      東莞欣隆全塑膠
      欣隆全塑膠

      專業工程塑料、塑膠原料經營商

      全國服務熱線

      18925783032

      塑膠原料
      塑膠原料wap
      當前位置:塑料經營商 >> 產品展示 >> PC塑膠原料 >> PC1414 SABIC EXL1414/沙伯基礎(GE)耐候塑料
      PC1414 SABIC  EXL1414/沙伯基礎(GE)耐候塑料

      PC1414 SABIC EXL1414/沙伯基礎(GE)耐候塑料

      PC1414 SABIC EXL1414/沙伯基礎(GE)耐候塑料

      全國24小時銷售熱線:

      18925783032
      產品介紹

      PC1414 SABIC  物性資料

      • 規格用途

      • 規格級別其它 其它 其它外觀顏色
        該料用途
        備注說明
      • 技術參數

      • 性能項目試驗條件[狀態]測試方法測試數據數據單位
        物理性能密度
        ISO 11831.19g/cm
        成型收縮率-,水平方向
        0.4-0.8%
        -,垂直方向
        0.4-0.8%
        吸水率
        ISO 620.35%
        機械性能屈服拉伸強度
        ASTM D63855MPa
        拉伸強度
        ASTM D63850MPa
        斷裂伸長率
        ASTM D63898%
        屈服伸長率
        ASTM D6386%
        彎曲強度
        ASTM D79092MPa
        彎曲模量
        ASTM D7902230MPa
        洛氏硬度
        ASTM D785121R
        Izod缺口沖擊強度23℃ASTM D256865J/m
        -30℃ASTM D256774J/m
        電氣性能體積電阻率
        ASTM D257>1.E+15Ohm.cm
        表面電阻率
        ASTM D257>1.E+15Ohm
        相對電阻率100HzASTM D1502.68
        介電消散因子100HzASTM D1500.0012
        熱性能維卡軟化溫度
        ASTM D1525145
        熱變形溫度-,0.45MpaASTM D648139
        -,1.82MpaASTM D648124

      英文PC1414物性資料

      TYPICAL PROPERTIES (1)
      MECHANICALValueUnitStandard
      Tensile Stress, yld, Type I, 50 mm/min560kgf/cm2ASTM D 638
      Tensile Stress, brk, Type I, 50 mm/min510kgf/cm2ASTM D 638
      Tensile Strain, yld, Type I, 50 mm/min6%ASTM D 638
      Tensile Strain, brk, Type I, 50 mm/min98%ASTM D 638
      Tensile Modulus, 50 mm/min20500kgf/cm2ASTM D 638
      Flexural Stress, yld, 1.3 mm/min, 50 mm span940kgf/cm2ASTM D 790
      Flexural Modulus, 1.3 mm/min, 50 mm span22700kgf/cm2ASTM D 790
      Hardness, Rockwell L89-ASTM D 785
      Hardness, Rockwell R121-ASTM D 785
      Tensile Stress, yield, 50 mm/min57MPaISO 527
      Tensile Stress, break, 50 mm/min60MPaISO 527
      Tensile Strain, yield, 50 mm/min6%ISO 527
      Tensile Strain, break, 50 mm/min120%ISO 527
      Tensile Modulus, 1 mm/min2150MPaISO 527
      Flexural Stress, yield, 2 mm/min85MPaISO 178
      Flexural Modulus, 2 mm/min2250MPaISO 178
      IMPACTValueUnitStandard
      Izod Impact, notched, 23°C88cm-kgf/cmASTM D 256
      Izod Impact, notched, -30°C78cm-kgf/cmASTM D 256
      Instrumented Impact Total Energy, 23°C714cm-kgfASTM D 3763
      Izod Impact, unnotched 80*10*3 +23°CNBkJ/m2ISO 180/1U
      Izod Impact, unnotched 80*10*3 -30°CNBkJ/m2ISO 180/1U
      Izod Impact, notched 80*10*3 +23°C70kJ/m2ISO 180/1A
      Izod Impact, notched 80*10*3 -30°C60kJ/m2ISO 180/1A
      Charpy 23°C , V-notch Edgew 80*10*3 sp=62mm70kJ/m2ISO 179/1eA
      Charpy -30°C , V-notch Edgew 80*10*3 sp=62mm65kJ/m2ISO 179/1eA
      Charpy 23°C , Unnotch Edgew 80*10*3 sp=62mmNBkJ/m2ISO 179/1eU
      Charpy -30°C , Unnotch Edgew 80*10*3 sp=62mmNBkJ/m2ISO 179/1eU
      THERMALValueUnitStandard
      Vicat Softening Temp, Rate B/50145°CASTM D 1525
      HDT, 0.45 MPa, 3.2 mm, unannealed139°CASTM D 648
      HDT, 1.82 MPa, 3.2mm, unannealed124°CASTM D 648
      CTE, -40°C to 40°C , flow6.96E-051/°CASTM E 831
      CTE, -40°C to 40°C , xflow7.47E-051/°CASTM E 831
      CTE, 23°C to 80°C , flow7.2E-051/°CISO 11359-2
      CTE, 23°C to 80°C , xflow7.2E-051/°CISO 11359-2
      Ball Pressure Test, 125°C +/- 2°CPasses-IEC 60695-10-2
      Vicat Softening Temp, Rate B/50145°CISO 306
      Vicat Softening Temp, Rate B/120146°CISO 306
      HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm140°CISO 75/Be
      HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm128°CISO 75/Ae
      Relative Temp Index, Elec130°CUL 746B
      Relative Temp Index, Mech w/impact120°CUL 746B
      Relative Temp Index, Mech w/o impact125°CUL 746B
      PHYSICALValueUnitStandard
      Specific Gravity1.18-ASTM D 792
      Mold Shrinkage, flow, 3.2 mm0.4 - 0.8%SABIC Method
      Mold Shrinkage, xflow, 3.2 mm0.4 - 0.8%SABIC Method
      Melt Flow Rate, 300°C /1.2 kgf10g/10 minASTM D 1238
      Density1.19g/cm2ISO 1183
      Water Absorption, (23°C /sat)0.35%ISO 62
      Moisture Absorption (23°C / 50% RH)0.15%ISO 62
      Melt Volume Rate, MVR at 300°C /1.2 kg9cm3/10 minISO 1133
      ELECTRICALValueUnitStandard
      Volume Resistivity>1.E+15Ohm-cmASTM D 257
      Surface Resistivity>1.E+15OhmASTM D 257
      Dielectric Strength, in oil, 0.8 mm16.2kV/mmASTM D 149
      Relative Permittivity, 100 Hz2.68-ASTM D 150
      Relative Permittivity, 1 MHz2.64-ASTM D 150
      Dissipation Factor, 100 Hz0.0012-ASTM D 150
      Dissipation Factor, 1 MHz0.0093-ASTM D 150
      FLAME CHARACTERISTICSValueUnitStandard
      UL Recognized, 94HB Flame Class Rating (3)0.4mmUL 94
      Glow Wire Flammability Index 850°C , passes at0.8mmIEC 60695-2-12
      Glow Wire Flammability Index 960°C , passes at1mmIEC 60695-2-12
      Glow Wire Ignitability Temperature, 1.0 mm875°CIEC 60695-2-13
      Glow Wire Ignitability Temperature, 3.0 mm875°CIEC 60695-2-13
      Processing


      Parameter
      Injection MoldingValueUnit
      Drying Temperature120°C
      Drying Time3 - 4hrs
      Drying Time (Cumulative)48hrs
      Maximum Moisture Content0.02%
      Melt Temperature295 - 315°C
      Nozzle Temperature290 - 310°C
      Front - Zone 3 Temperature295 - 315°C
      Middle - Zone 2 Temperature280 - 305°C
      Rear - Zone 1 Temperature215 - 295°C
      Mold Temperature70 - 95°C
      Back Pressure0.3 - 0.7MPa
      Screw Speed40 - 70rpm
      Shot to Cylinder Size40 - 60%
      Vent Depth0.025 - 0.076mm


      相關產品

        人妻丰满熟妇av无码区HD
        <big id="x777x"></big>

            <p id="x777x"></p>
            <track id="x777x"><strike id="x777x"><strike id="x777x"></strike></strike></track>
            <pre id="x777x"></pre>

            <address id="x777x"><strike id="x777x"><span id="x777x"></span></strike></address>